Click here to sign in with or

by Dana Desonie, Argonne National Laboratory

(Phys.org) —Toxic vehicle emissions, such as carbon monoxide and unburned hydrocarbons, are chemically converted to benign compounds, like carbon dioxide (CO2) and water, by catalytic converters. Although catalytic converters are valuable technology, they are also expensive. To reduce costs, experiments are being done to lessen the amount of platinum (Pt) and substitute palladium (Pd) in converters. The U.S. Department of Energy Office of Science's Advanced Photon Source (APS) played a role in research that indicates a Pd/lanthanum (La)-alumina catalyst may result in a less-expensive catalytic converter with improved low-temperature carbon monoxide (CO) oxidation reactivity.

Catalytic converters, installed on vehicles with internal combustion and diesel engines, convert the toxic byproducts of combustion to less toxic compounds. In two-way (lean burn) converters, used primarily on diesel engines, CO and partially burned hydrocarbons are oxidized over a Pt or Pd catalyst to form CO2 and water. In addition, three-way (stoichiometric) converters, used on internal combustion engines, also reduce nitrogen oxides back to nitrogen. This is tremendously beneficial since nitrous oxide is 300 times more potent as a greenhouse gas than is CO2. Since diesel exhaust is cooler than gasoline exhaust, the two-way catalyst must perform at low temperatures and also survive severe exothermic reactions when the particulate filter in the catalyst regenerates.

The oxidizing and reducing catalysts in catalytic converters contain precious metals, especially the costly platinum group metals Pt and Pd; a Pt-Pd alloy is more effective than either metal alone. To keep costs down, manufacturers try to minimize the amount of catalyst required, or to use less expensive catalysts. The high cost of Pt has led to research to determine the hydrothermal stability of Pd, without the addition of Pt, particularly with La-alumina support.

Researchers from the University of New Mexico and Argonne National Laboratory simulated diesel oxidation catalysts with 2.5% Pd and tested in two different preparations, one with alumina only and one with La-stabilized alumina. Each catalyst was roasted to 500° C to oxidize the Pd to PdO and then cooled to room temperature. When the temperature was raised to 140° C in the presence of CO, the PdO reduced to Pd metal. Results of the experiments were analyzed by x-ray absorption spectroscopy (XAS) and diffuse reflectance Fourier transform infrared spectroscopy (DRIFTS) at the X-ray Science Division 9-BM beamline at the Argonne National Laboratory Advanced Photon Source.

With the Pd-alumina catalyst, the absorption of CO was found to be irreversible because the catalyst had little reaction with oxygen. With the La-stabilized alumina, the Pd catalyst was more reactive toward oxygen and had higher CO conversion; CO oxidation began at a lower temperature, around 100° C. Pd became oxidized when the gas phase was switched from pure CO to the stoichiometric reaction mixture, and there was a reduction in the surface coverage of CO.

The addition of La to the catalyst had two effects. First, Pd formed small particles and clusters, which increased Pd dispersion from 17% to 26%. The increase in dispersion is partially responsible for the improved CO conversion.

Second, the redox reaction was more likely at low temperature, so Pd was less susceptible to CO poisoning. The turnover frequency at 140° C improved 5-fold, due in part to the redox behavior of the Pd/La-alumina catalyst.

In catalytic converters, a Pt-Pd alloy is more stable, more reactive, and less susceptible to aging than Pt metal alone. Adding Pd in the alloy reduces the cost, hence the hydrothermal stability of Pd is important. The use of simultaneous XAS and DRIFTS in this research leads to a greater understanding of the effects of adding La to Pd-based catalysts in catalytic converters to improve the efficiency and decrease the costs of two-way catalytic converters used for diesel engines. Explore further New catalytic converter could cut fuel consumption and car manufacturing costs More information: Jason R. Gaudet, Andrew de la Riva, Eric J. Peterson, Trudy Bolin, and Abhaya K. Datye, "Improved Low-Temperature CO Oxidation Performance of Pd Supported on La-Stabilized Alumina," ACS Catal. 3, 846 (2013). DOI: 10.1021/cs400024u Provided by Argonne National Laboratory Citation: Improved low-temperature performance of catalytic converters (2014, January 30) retrieved 14 May 2022 from https://phys.org/news/2014-01-low-temperature-catalytic.html This document is subject to copyright. Apart from any fair dealing for the purpose of private study or research, no part may be reproduced without the written permission. The content is provided for information purposes only.

More from Physics Forums | Science Articles, Homework Help, Discussion

Use this form if you have come across a typo, inaccuracy or would like to send an edit request for the content on this page. For general inquiries, please use our contact form. For general feedback, use the public comments section below (please adhere to guidelines).

Please select the most appropriate category to facilitate processing of your request

Thank you for taking time to provide your feedback to the editors.

Your feedback is important to us. However, we do not guarantee individual replies due to the high volume of messages.

Your email address is used only to let the recipient know who sent the email. Neither your address nor the recipient's address will be used for any other purpose. The information you enter will appear in your e-mail message and is not retained by Phys.org in any form.

Get weekly and/or daily updates delivered to your inbox. You can unsubscribe at any time and we'll never share your details to third parties.

Medical research advances and health news

The latest engineering, electronics and technology advances

The most comprehensive sci-tech news coverage on the web

This site uses cookies to assist with navigation, analyse your use of our services, collect data for ads personalisation and provide content from third parties. By using our site, you acknowledge that you have read and understand our Privacy Policy and Terms of Use.